EXUP Worldwide

i feel bad no one knows your delema, i just figured ide respond so you didnt think you were invisable. i dont know an awnser, but here is a reply..<br><br>zoid <p></p><i></i>

haris, i have heard that, but it wasnt the chain, or i dont think it was. mine was at freeway speeds, and it happened like once or twice a mile, then nothing for days. it was wierd... when it did happen, i thought something catostrophic would happen if i didnt figgure it out, but eventually it went ...

ok, time for another question i shouldnt ask, but im going to anyway.<br><br>the bike is an 89, im about to mount a 98 yzf 750 shock on it, and since ive raised the rear end via the dog bones, the shock goes through the swing arm at a tad of an angle. not bad, but a little more snug than stock. the ...

funny i just put one in.<br><br>there are three types of plates we shall call them normal, thin and thick.<br><br>first put in four normals, and four steel (friction first.)<br><br>then put in the wierd spring, and the thin plate, it dosent matter what goes in first, they occupy the same space<br><b...

i had the barnet also, and noticed the same thing on my almost stocker. at like 8 or 9 it would just break free. chuckd said that the aftermarket clutches do this. if you take out your stock clutch, you notice there is a strange spring in between the number 7 and 8 plates or so. somehow this didnt f...

i keep all fzr1000 jetting advise in a word file, and keep it close to my heart. below are two posts from members from a few months agow<br><br>first post<br><br>I have a 1990 FZR 1000 with a dynojet stage one jet kit, K&N filter and a Vance and Hines slip-on. Does anyone know the baseline settings ...

i was dooing my clutch and noticed an odd spring between the 7th fiber plate and 8th steel one. it looked a big washer, the diamater of one of the plates, but thiner. it was wavy so it pushed the plates apart. when i put the new barnet clutch in, it all bareley fit in with the spring in. once all to...

ok, im sold, ill start to look for one. question on it, do i need to tear down the engine to put the clutch basket in???? im not looking forward to spliting the cases. <br><br>zoid <p></p><i></i>

i ride about 150 miles a day, and some times do wheelies, i used to just launch it hard from the start, and it would come up. i dont ride it, just bring it up, then down. but now, i get to a crawling pace, pull in the clutch, rev up to like 5k, fether the clutch, and gas it smoothley. <br><br>i dont...

is it running lean down low??? mine does that when my jetting is off in that direction.<br><br>zoid <p></p><i></i>

wow, i didnt know that!!! my tight, non oil burning 90 fzr1000 needed a seccond gear, i took it to a local shop who (or couse) took it all the way down to swap the gears, and shift fork. while it was appart, i asked if i could get a light hone, and new rings. the shop tole me the cylinders look perf...

what thread was that that you chatted about it, what air filter do you use with your trick air box??? if i just made a decision between the stock air box, and individual filters, is the same info true, or does it lean twards the individuals more than??? i really dont want to loose that great mid ran...

thank you, that is deffinetley food for thought, do you have a drop in filter??? <br><br>zoid <p></p><i></i>

i was bored, so i did the airbox drilling, and pulled the smog on my bike. i know ive covered this allready, but this is going somewhere. <br><br>the bike runs tons better, and think now the bike runs rich from the factory in the middle. anyway, looking at the air box i was thinking, is this thing r...

thanks, i was thinking of sending the head out to lap the valves, and replace the seals, or can i do this also??? did you notice a power gain??? did you have to rejet again??? did you do any polishing????? yes i was going to do the rings also.<br><br>thanks again for the tip, please more though.<br>...

im starting work on my seccond motor, the motor that sucked a quart of oil each few hundred miles. anyhoo, i wanted to port and do a three angle valve job, i was going to send it out, but a buddie was telling me, i can do allot of the work via a dremmel. <br><br>he said that its pretty easy to pull ...