Ultrasonic Cleaner
-
- Dolphin-headed purple plasma TLR thing?
- Posts: 3837
- Joined: Mon Jan 29, 2007 7:12 pm
- Location: Melbourne. Australia
Ultrasonic Cleaner
Using my 30 lt Ultrasonic Cleaner for the first time in anger. It's a beauty, It is large enough to clean all engine components including crankcases. Here's Jason's ZX9R cases being cleaned, and a sump that has been through. The cases are cleaned in two haves obviously
Re: Ultrasonic Cleaner
That's definitely on my "need one" tools list.
VRRA Competition Coordinator
BRS Racing #61
BRS Racing #61
-
- Dolphin-headed purple plasma TLR thing?
- Posts: 3837
- Joined: Mon Jan 29, 2007 7:12 pm
- Location: Melbourne. Australia
Re: Ultrasonic Cleaner
The best thing is no elbow grease required, and no chemicals, Just water and dishwashing detergent. Dry out parts in the oven afterwards at low heat. And then CRC.
I heat the water to about 50 degrees C, and do bursts of 5 minutes so the transducers are not stressed (over heat). Probably 30 minutes on the crankcase turning as we go. Even the corrosion comes off!
I'll do some before and after photo's on the lower cases.
I heat the water to about 50 degrees C, and do bursts of 5 minutes so the transducers are not stressed (over heat). Probably 30 minutes on the crankcase turning as we go. Even the corrosion comes off!
I'll do some before and after photo's on the lower cases.
-
- Help!!! I need a LIFE!!!
- Posts: 518
- Joined: Sun May 27, 2007 2:27 am
- Location: Aberdeenshire, UK
Re: Ultrasonic Cleaner
They're great aren't they! I've got a 10 litre one.
Interesting comment about your washing fluid. I spray the parts with SDoc and leave to soak for a while then add in a capful of heavy aluminium engine degreaser, and then leave them to do the business for 20 minute runs at about 50 to 60 deg C.
I've heard others using the normal fairy liquid washing up soap, so I'll give that a go next time I've got some parts to clean.
Dave
Interesting comment about your washing fluid. I spray the parts with SDoc and leave to soak for a while then add in a capful of heavy aluminium engine degreaser, and then leave them to do the business for 20 minute runs at about 50 to 60 deg C.
I've heard others using the normal fairy liquid washing up soap, so I'll give that a go next time I've got some parts to clean.
Dave
1993 YZF 750 SP with Yoshimura half system
RG400
GSXR 1100WT
RG400
GSXR 1100WT
-
- Dolphin-headed purple plasma TLR thing?
- Posts: 3837
- Joined: Mon Jan 29, 2007 7:12 pm
- Location: Melbourne. Australia
Re: Ultrasonic Cleaner
Yes they are! Here's a comparison the upper crankcase washed, and the lower unwashed. They were obviously in the same state.
I use a dishwashing liquid called earth first. It's cheap and know to have an alkaline PH. I put a fair bit into mine. Otherwise I would use truck wash. Anything alkaline is fine. Plain water will clean as well, due to the fact it is cavitation within the liquid that does the cleaning. I just figure it can't hurt to chuck some soap in.
Before:
After:
I use a dishwashing liquid called earth first. It's cheap and know to have an alkaline PH. I put a fair bit into mine. Otherwise I would use truck wash. Anything alkaline is fine. Plain water will clean as well, due to the fact it is cavitation within the liquid that does the cleaning. I just figure it can't hurt to chuck some soap in.
Before:
After:
-
- Dolphin-headed purple plasma TLR thing?
- Posts: 3837
- Joined: Mon Jan 29, 2007 7:12 pm
- Location: Melbourne. Australia
Re: Ultrasonic Cleaner
Here is the lower after cleaning... You can tell I'm happy about this addition to the shed And only 400 au or so pesos! I can promise you that no scrubbing was involved. The fact that corrosion is actually mitigated is outstanding!
Last edited by spook on Sun Feb 19, 2017 1:39 am, edited 2 times in total.
-
- Dolphin-headed purple plasma TLR thing?
- Posts: 3837
- Joined: Mon Jan 29, 2007 7:12 pm
- Location: Melbourne. Australia
Re: Ultrasonic Cleaner
I'll start an off topic post on Jason's ZX9 race engine instal into his ex-works M1. I'm having fun with the build, hopefully we will be ready for Jason to contest the Vic titles
-
- Help!!! I need a LIFE!!!
- Posts: 3519
- Joined: Thu Jan 26, 2006 6:35 pm
- Location: Edmonton, Alberta
Re: Ultrasonic Cleaner
Why are you putting a kawi engine in an M1?
Michael
Yes Yes I know, I said, I'm building a project YZF1070
Basement is done now, 850 finished and gone...
Gotta get the new siding up on the house.
Fixing the FZ1 up, cleaning up garage and then I might even begin
Yes Yes I know, I said, I'm building a project YZF1070
Basement is done now, 850 finished and gone...
Gotta get the new siding up on the house.
Fixing the FZ1 up, cleaning up garage and then I might even begin
-
- Dolphin-headed purple plasma TLR thing?
- Posts: 3837
- Joined: Mon Jan 29, 2007 7:12 pm
- Location: Melbourne. Australia
Re: Ultrasonic Cleaner
Michael, it's a 1994 Kawasaki ZX7RR M1, Homologation special. Ex-works Superbike.
-
- Help!!! I need a LIFE!!!
- Posts: 3519
- Joined: Thu Jan 26, 2006 6:35 pm
- Location: Edmonton, Alberta
Re: Ultrasonic Cleaner
that makes a bit more sense,
What year is the ZX9 motor? Just interested as it took yamaha until it's first R1 iteration to put the cam sprockets on the end of the cams.
What year is the ZX9 motor? Just interested as it took yamaha until it's first R1 iteration to put the cam sprockets on the end of the cams.
Michael
Yes Yes I know, I said, I'm building a project YZF1070
Basement is done now, 850 finished and gone...
Gotta get the new siding up on the house.
Fixing the FZ1 up, cleaning up garage and then I might even begin
Yes Yes I know, I said, I'm building a project YZF1070
Basement is done now, 850 finished and gone...
Gotta get the new siding up on the house.
Fixing the FZ1 up, cleaning up garage and then I might even begin
-
- Dolphin-headed purple plasma TLR thing?
- Posts: 3837
- Joined: Mon Jan 29, 2007 7:12 pm
- Location: Melbourne. Australia
Re: Ultrasonic Cleaner
Motor is a ZX9R B1 1994, ZX7RR M1 is 94 also.