weak or rich

exupjon · Post by **exupjon** » Sun Aug 08, 2004 7:03 am

put my carbs back to standard finaly got it to run ,lo end 1000,4000 spot on 5000,7500 no power flat and soggyis it weak or rich which way do i move the needle<img src=http://www.ezboard.com/images/emoticons/eyes.gif ALT=":rolleyes"> <img src=http://www.ezboard.com/images/emoticons/eyes.gif ALT=":rolleyes"> its got kn filter and a viper race can should i put a stock filter back in?? Edited by: <A HREF=http://p072.ezboard.com/bexupbrotherhoo ... exupjon</A> at: 8/8/04 5:05 am

dragracer1951 · Post by **dragracer1951** » Sun Aug 08, 2004 7:36 am

have you done a plug chop? have you tried to block off half the air box intake to simulate rich? these will give you an indication of which way you need to go I would think that if you have stock jetting and your carbs are clean, you may have to put a shim under the needle clip. go to the hardware store and get four washers aprox .020 thick for under the clips which will richen the midrange slightly Jim

flyingcircus68 · Post by **flyingcircus68** » Sun Aug 08, 2004 5:12 pm

Usually, when you throttle it on and it feels flat without breaking up, it's running lean. It should feel a little better if you let it idle and let it get hot enough to trip the fan. A good way to check is to do what drag racer mentioned. But, you could also quickly check by having a buddy ride behind you to look for smoke. If your running really rich, you'll leave a trail of black smoke. You'll get it squared away after a few tries. <img src=http://img.photobucket.com/albums/v209/ ... ock_On.gif ALT=":rock"> <img src=http://img.photobucket.com/albums/v209/ ... Banger.gif ALT=":headbanger">

exupjon · Post by **exupjon** » Wed Aug 11, 2004 11:51 am

its blowing flames out?? 9000/12000 its popping and banging is this normal flames look cool but this set up should be weak not rich ime getting realy confused<img src=http://www.ezboard.com/images/emoticons/mad.gif ALT=">:"> <img src=http://www.ezboard.com/images/emoticons/mad.gif ALT=">:"> <img src=http://www.ezboard.com/images/emoticons/mad.gif ALT=">:">

flyingcircus68 · Post by **flyingcircus68** » Wed Aug 11, 2004 4:37 pm

<img src=http://img.photobucket.com/albums/v209/ ... oapbox.gif ALT=":soap">

flyingcircus68 · Post by **flyingcircus68** » Wed Aug 11, 2004 4:42 pm

Sorry about the multiple posts. I tried to include the soap box emoticon and pointed to it with an arrow. I guess that violated some HTML rule. I'm to ignorant to know what that is exactly.<img src=http://www.ezboard.com/images/emoticons/indifferent.gif ALT=":|"> Back to your topic. It appears that you're either far enough away from optimum that you can't passively make an assesment. Start with the restricting the air box inlet. That should tell you which way to go. p.s. make sure that you're starting with new plugs.

exupjon · Post by **exupjon** » Mon Aug 30, 2004 9:28 am

ive sorted it and now its like sh1t off a stick,finaly managed to put a photo on if anybody is interested<img src=http://www.ezboard.com/images/emoticons/roll.gif ALT=":rollin"> <img src=http://www.ezboard.com/images/emoticons/roll.gif ALT=":rollin">

flyingcircus68 · Post by **flyingcircus68** » Mon Aug 30, 2004 11:01 am

In the interest of satisfying everyones curiosity, why don't you post the jetting parameters that you settled on.

exupjon · Post by **exupjon** » Mon Aug 30, 2004 11:34 am

changed k/n for hi flow, needle clip 2nd from bottom air screw 3.25 out float hight 12mm hope this helps<img src=http://img.photobucket.com/albums/v209/ ... ananna.gif ALT=":bananna">

EXUP Worldwide

weak or rich

weak or rich

have you...

Re: have you...

flames

Re: flames

Re: flames

oh yes oh yes

Re: flames

Re: oh yes oh yes