weekend project
-
- New Poster
- Posts: 32
- Joined: Wed Jun 09, 2004 10:02 am
weekend project
Hi all, Im going to tackle changing my oil filter and oil this weekend, and wanted to know how many quartz does the FZR 1000 take and whats the best filter and oil to use.. I was going to buy it from the dealer 20w40 <br><br>thanks<br><br> <p></p><i></i>
-
- Help!!! I need a LIFE!!!
- Posts: 968
- Joined: Fri Mar 26, 2004 1:06 pm
- Location: South Bend, IN
Re: weekend project
My bike (87) usually takes about 3 1/2 qts. So if you pick up 4 qts you'll have enough plus some leftover. I run 20/40 as well.<br><br>Does your year have a spin-on filter, or is it like mine where it's an assembly you take apart to replace the filter element? <p><!--EZCODE ITALIC START--><em>"I have come here to chew bubble-gum and kick ass...<br>and I'm all out of bubble-gum."</em><!--EZCODE ITALIC END--><br><!--EZCODE IMAGE START--><img src="http://members.optusnet.com.au/lanemeye ... karate.gif" style="border:0;"/><!--EZCODE IMAGE END--></p><i></i>
-
- Help!!! I need a LIFE!!!
- Posts: 2535
- Joined: Fri Jan 02, 2004 1:10 pm
- Location: Bremerton, Wa
filters
I got a couple filters from the dealer then found out that Wal Mart has em<br>for less<br>And I won' ttouch an oil thread with a ten foot mouse cord!<br>Jim <p></p><i></i>
-
- Help!!! I need a LIFE!!!
- Posts: 968
- Joined: Fri Mar 26, 2004 1:06 pm
- Location: South Bend, IN
Re: filters
I've checked Wal-Mart before, but they cut off the FZRs at 89 or 90 (I think). Places like Autozone can get them, but it's a flip of the coin if they'll have them in stock. <p><!--EZCODE ITALIC START--><em>"I have come here to chew bubble-gum and kick ass...<br>and I'm all out of bubble-gum."</em><!--EZCODE ITALIC END--><br><!--EZCODE IMAGE START--><img src="http://members.optusnet.com.au/lanemeye ... karate.gif" style="border:0;"/><!--EZCODE IMAGE END--></p><i></i>
-
- New Poster
- Posts: 32
- Joined: Wed Jun 09, 2004 10:02 am
Re: filters
thanks guyz, my is not the spin-off (I think), what is the part number if I buy at Autozone or Walmart, can I also get the oil at AutoZone or Walmart too? <p></p><i></i>
-
- Help!!! I need a LIFE!!!
- Posts: 968
- Joined: Fri Mar 26, 2004 1:06 pm
- Location: South Bend, IN
Re: filters
As far as the filter goes...just give them your bike info and they can look it up for you. Like I said they may not have it in stock and may have to order it. I know the pricing at Autozone was cheaper than what it was at my local shop.<br><br>Oil however is doubtful. At least around here (northern Indiana) NOBODY carries the 20/40 except the bike shops. Wal-Mart had 20/50, but I opted to stick with 20/40. <br><br>Also, I would recommend replacing the big O-ring that goes on the lip of the filter housing. Should only be a couple bucks, and it will help seal the housing to the block.<br><br>One last thing...when you go to put the assembly back on, be careful when tightening down the bolt since that is actually part of the filter. If you tighten it down too far you can crack the filter housing....trust me I found out the hard way! <p><!--EZCODE ITALIC START--><em>"I have come here to chew bubble-gum and kick ass...<br>and I'm all out of bubble-gum."</em><!--EZCODE ITALIC END--><br><!--EZCODE IMAGE START--><img src="http://members.optusnet.com.au/lanemeye ... karate.gif" style="border:0;"/><!--EZCODE IMAGE END--></p><i></i>
-
- New Poster
- Posts: 32
- Joined: Wed Jun 09, 2004 10:02 am
Re: filters
thanks again everyone. I called Autozone and it 3.99 and they carry 20w40. ( Salt Lake City, Utah) <p></p><i></i>
Drain Plug Gasket
The oil drain plug has a metal gasket that your suppose to replace with each oil change. Yamaha dealer has them for approximately $0.97 or so. Gasket allows you to snug the drain plug without over tightening it or having any oil leak. Oil drain plug torque spec is 31 ft. lbs. (43 Nm). I don't know if it's ever happened, but they caution against over tightening the drain plug to avoid damage to the crankcase. <br>Don <p></p><i></i>
-
- Help!!! I need a LIFE!!!
- Posts: 968
- Joined: Fri Mar 26, 2004 1:06 pm
- Location: South Bend, IN
Re: Drain Plug Gasket
Oops...forgot to mentiont that one too (thanks Don). <br><br>One other o-ring to consider replacing: There is another small one that is on the filter bolt. It provides a seal between the filter element cover and the filter bolt. This is another one that is a cheapie so you may want to grab one of those too.<br><br>Once you get the assembly apart check the spring and washer to see if they are ok. These are cheap to replace as well if you need to. Long as they look in good shape you should be fine.<br><br> <p><!--EZCODE ITALIC START--><em>"I have come here to chew bubble-gum and kick ass...<br>and I'm all out of bubble-gum."</em><!--EZCODE ITALIC END--><br><!--EZCODE IMAGE START--><img src="http://members.optusnet.com.au/lanemeye ... karate.gif" style="border:0;"/><!--EZCODE IMAGE END--></p><i></i>
-
- New Poster
- Posts: 32
- Joined: Wed Jun 09, 2004 10:02 am
Re: Drain Plug Gasket
Hey thanks for all the advice. I bought the o-ring and the gasket. so you guyz know if you special order the oil filter at Checkers, it will come with a gasket for the oil filter and a plastic o-ring instead of metal. this will save your about $7.00 from the dealer. <p></p><i></i>