Hoses

akcribs · Post by **akcribs** » Tue Oct 21, 2003 2:43 am

I need help routing and attaching the hoses and tubing below th Fuel Tank. They are all mixed up now. I don't know what goes where. I would really like a diagra of all hoses, large and small, and where they attach.

cterror · Post by **cterror** » Tue Oct 21, 2003 3:16 am

now im not shure which bike you are talking about but heres the spex for yzf750. should work out for fizzers as well. correct someone if i state wrong 1. gas<img src=http://www.ezboard.com/images/emoticons/frown.gif ALT=":("> big hose abt 5mm diam) other end big connection in the tank, other between carburators.. in the middle. 2. vacum hose: (small hose abt 2,5mm diam) other end tank smaller connection and other end cylinder no4 (right from sitting position) just in front of carburator. i do not know the right word for this part in english=/... rubber that attaches carburator to block. quite hard to find but it is about the only connection you can plug it to. 3. big tube. (abt 10mm diam) other end near the oil filler-cap, on the upper side of engine, and the other to airbox. there is an big connection on the airbox. 4. all the downward hanging hoses from carburator just down. i usually put besides the engine or throught the hole between engine and rearfork. hope this helps. ask more specificly if you run into trouble

cterror · Post by **cterror** » Tue Oct 21, 2003 5:57 am

shait... i forgot that fizzers have gaspump separately. if you have an fzr then you have to attach the gas lines from tank to gaspump and then to carburators

flyingcircus68 · Post by **flyingcircus68** » Tue Oct 21, 2003 6:02 am

akcribs, if your looking for a specific answer, you need to start with a more specific question.

akcribs · Post by **akcribs** » Wed Oct 22, 2003 2:41 am

Thanks so far guys. The problem is that I have changed engines and I need to know where each hose connects. (both ends) 1:Vacuum 2:Coolant 3:Cooling overflow or whatever it is. I can see 3 hoses that just hang like drain lines down underneath near the kickstand. I don't know where they come from. If someone will send me a diagram or two that would be great. Basicall I need to know where each port is and where the other port is for the other end of the hose. I am especially concerned with the vacuum lines. She idles rough and I can see black soot starting to forming on the tail pipe. After reving past 3,000 RPM she is smooth and powerful. I think I need to get the vacuum hoses in order first before adjusting anything.

cterror · Post by **cterror** » Wed Oct 22, 2003 3:51 am

ok. your problem is not hose relaited. the vacuum hose goes from carburator intace to fuelsystem. 2. coolant?.. if there is nothing wrong with it, why would you want to change anything? generally the coolant overflow (the one that collects to the bottle under seat) is connecter in the radiator cap, so that when the cap under high pressure (high temperature) lifts, it can collect the water in the coolant bottle. 3. the 3 hoses hangin could be tank-air hose and some overflows from carburators. nothing to be quite alarmed for, but do take your tank off if you want to be sertain. ....4... your problem. i should think that your needle jets are worn and needs to be replased. that is the main reason for rough idle and poor running under 3-4krpm. there are several posts about it and here is the link to factorypro who sells repairs to them. reed it and then ask for more info if it does not open <a href="http://www.factorypro.com/tech/needle_jet_Mikuni.html" target="top">www.factorypro.com/tech/needle_jet_Miku ...

akcribs · Post by **akcribs** » Thu Oct 23, 2003 1:32 am

OK. Lets just talk vacuum hoses. You say from carburetor to fuel system. Can you be more specific. Can you list each vacuum hose and where exactly it connects.

cterror · Post by **cterror** » Fri Oct 24, 2003 12:02 am

i think that someone with an org fzr should answer this as the vacumes goes different in yzf becourse of the fuelpump located inside the tank. and i just hava one vacum hose. from tank bottom to intake manifold no 4. to the backside of it. sorry but cant help more<img src=http://www.ezboard.com/images/emoticons/frown.gif ALT=":(">

akcribs · Post by **akcribs** » Fri Oct 31, 2003 1:17 am

Thanks Cterror. Hoses are routed OK now. I just had come duplicate hoses and. Some were still on the bike. Some were still on the new engine. I just had to remove the extra hoses and everything lined up as you said.

cterror · Post by **cterror** » Fri Oct 31, 2003 1:26 am

good thing that you got it sorted! happy riding

NightDevil · Post by **NightDevil** » Tue Nov 04, 2003 4:17 am

Maybe this will help... <img src="http://grm.m.walla.co.il/briefcase/00f3 ... _10_03.jpg" style="border:0;"/> Goodl luck E :-) TheNightDevil :-)

nana800 · Post by **nana800** » Wed Nov 05, 2003 9:55 am

dont know if this will work but tried to post photo fzr750genesis airbox [img noborder]<a href="http://C<img src=http://www.ezboard.com/images/emoticons/ohwell.gif ALT=":\"> My">C<img src=http://www.ezboard.com/images/emoticons/ohwell.gif ALT=":\"> My</a> Documents\photo\motorbikes\yzf750\air box.jpg[/img] gray(uk)

nana800 · Post by **nana800** » Wed Nov 05, 2003 10:04 am

sorry cant post photo,e mail Gghealey@aol.com and i will send two gray

EXUP Worldwide

Hoses

Hoses

Re: Hoses

Re: Hoses

Re: Hoses

Hoses on 1990 FZR1000

Re: Hoses on 1990 FZR1000

Hoses on 1990 FZR1000

Re: Hoses on 1990 FZR1000

Hoses on 1990 FZR1000

Re: Hoses on 1990 FZR1000

Picture

Re: Hoses

Re: Hoses photo